WaterLesson 3 of 7
Wells and pumps
What you’ll learn
- How well types differ and where a well can safely go
- How to protect the wellhead and what permits and water rights may apply
- How pumps, pressure switches and pressure tanks work, and how to size them
- What to do after a flood, and how shock chlorination is done
- The electrical, confined-space and generator rules that keep you alive
The short version
Test a private well every year for total coliform, nitrate, TDS and pH at a state-certified lab, and again after floods, repairs or a change in taste or smell.
Keep a well 50 ft or more from septic tanks and livestock yards and 100 ft or more from drain fields in most states. Check your state's table.
Don't turn on a flooded well's pump until a qualified person checks the wiring, and never enter a well pit.
Know your water right. In Colorado, Utah and other western states you can't take ditch or creek water, or use some wells outdoors, without one.
Well types and siting
Dug or bored wells are about 10–30 ft deep and not cased continuously; driven wells are about 30–50 ft; drilled wells are continuously cased and can run thousands of feet. Shallow wells are more likely to be contaminated by surface water, septic systems or spills, and they go dry in drought.
Put the well at the highest practical spot, not down slope from contamination, not where runoff ponds, and not in a basement, pit or building other than a well house.
Sources: U.S. Environmental Protection Agency, Minnesota Department of Health, Well Management Section and 10 more
- U.S. Environmental Protection Agency. Learn About Private Water Wells
- Minnesota Department of Health, Well Management Section. Well Owner's Handbook: A Consumer's Guide to Water Wells in Minnesota (4th ed., updated January 2014)
- CDC. Well Water Safety
- U.S. Geological Survey. Groundwater Wells (USGS Water Science School; adapted from "Ground Water and the Rural Homeowner", USGS 1982)
- Minnesota Pollution Control Agency. Minnesota Rules, part 4725.4450 — Water-Supply Well Distances from Contamination
- Wisconsin Legislative Reference Bureau. Wisconsin Administrative Code ch. NR 812 — Well Construction and Pump Installation (s. NR 812.08 location and Table A; s. NR 812.26 filling and sealing)
- Washington State Legislature. WAC 173-160-171 — What are the requirements for the location of the well site and access to the well?
- North Carolina Office of Administrative Hearings. 15A NCAC 02C .0107 — Standards of Construction: Water Supply Wells
- New York State Department of Health. New York State Sanitary Code, 10 NYCRR Part 5, Subpart 5-1, Appendix 5-B — Standards for Water Wells
- Georgia Department of Public Health, Environmental Health. Well Water (Individual Private Wells: location, installation, maintenance, sampling, abandonment)
- Florida Legislature. Florida Statutes s. 381.0065 — Onsite sewage treatment and disposal systems; regulation (subsection (4)(h) setbacks)
- Colorado Water Quality Control Commission. Regulation No. 43 — On-Site Wastewater Treatment System Regulation, 5 CCR 1002-43 (s. 43.7, Table 7-1 well distances), effective May 19, 2026
Wellhead protection
Casing height: 12 in above ground in Wisconsin, North Carolina, New York and Texas, 18 in in Utah; Penn State recommends 8 in. Flood-prone sites need more (2 ft above the flood level in Wisconsin and Georgia).
Grade the ground to slope away; use a vermin-proof, weatherproof cap with a screened vent.
Grout and seal: Minnesota requires grout pumped in from the bottom up, never poured from the surface; New York casing runs from 1 ft above grade to 19 ft below with grout.
Abandoned wells must be properly filled and sealed; Texas makes the landowner liable; Minnesota lets only licensed contractors seal them.
Sources: Wisconsin Legislative Reference Bureau, North Carolina Office of Administrative Hearings and 9 more
- Wisconsin Legislative Reference Bureau. Wisconsin Administrative Code ch. NR 812 — Well Construction and Pump Installation (s. NR 812.08 location and Table A; s. NR 812.26 filling and sealing)
- North Carolina Office of Administrative Hearings. 15A NCAC 02C .0107 — Standards of Construction: Water Supply Wells
- New York State Department of Health. New York State Sanitary Code, 10 NYCRR Part 5, Subpart 5-1, Appendix 5-B — Standards for Water Wells
- Utah Division of Water Rights, Office of the State Engineer. State of Utah Water Well Handbook Based on the Administrative Rules for Water Wells (R655-4 UAC), July 2022 version
- Texas A&M AgriLife Extension Service, Texas Well Owner Network. Texas Well Owner Network: Well Owner's Guide to Water Supply (ESC-029, 04/19)
- Penn State Extension. Drilling a New Well
- Georgia Department of Public Health, Environmental Health. Well Water (Individual Private Wells: location, installation, maintenance, sampling, abandonment)
- U.S. Environmental Protection Agency. Learn About Private Water Wells
- U.S. Environmental Protection Agency. Protect Your Home's Water
- Nebraska Extension. Private Drinking Water Wells: Operation and Maintenance for Mechanical Components (NebGuide G2153)
- Minnesota Department of Health, Well Management Section. Well Owner's Handbook: A Consumer's Guide to Water Wells in Minnesota (4th ed., updated January 2014)
- CDC. Well Water Safety
Permits and rights (checked 2026-10-04)
Licensed drillers are required in many states. Minnesota, Wisconsin and Utah let owners build a well or install a pump on their own land under conditions; Georgia requires a licensed contractor and notice to the county.
Colorado: exempt wells are generally limited to 15 gpm and, on small parcels, to household use inside one dwelling; permit review can take up to 49 days.
Utah: every well needs State Engineer approval.
Texas: groundwater districts exempt domestic and livestock wells on 10+ acres under 25,000 gal a day. Washington: permit exemption for 5,000 gal a day domestic and a half-acre of lawn and garden.
Sources: Minnesota Department of Health, Well Management Section, Wisconsin Legislative Reference Bureau and 8 more
- Minnesota Department of Health, Well Management Section. Well Owner's Handbook: A Consumer's Guide to Water Wells in Minnesota (4th ed., updated January 2014)
- Wisconsin Legislative Reference Bureau. Wisconsin Administrative Code ch. NR 812 — Well Construction and Pump Installation (s. NR 812.08 location and Table A; s. NR 812.26 filling and sealing)
- Utah Division of Water Rights, Office of the State Engineer. State of Utah Water Well Handbook Based on the Administrative Rules for Water Wells (R655-4 UAC), July 2022 version
- Georgia Department of Public Health, Environmental Health. Well Water (Individual Private Wells: location, installation, maintenance, sampling, abandonment)
- Colorado Division of Water Resources. Guideline 2023-1: Uses of Water From Exempt and Small Capacity Wells
- Colorado State University Extension. Colorado Water Law and How to Garden Anyway
- Colorado Division of Water Resources, Department of Natural Resources. Well Permitting (Division of Water Resources)
- Utah Division of Water Rights. FAQ's (Utah Division of Water Rights)
- Texas A&M AgriLife Extension Service. Basics of Texas Water Law (AgriLife Extension publication, 1/18)
- Washington State Department of Ecology. Groundwater permit exemption
Pumps and pressure tanks
| Pump | Use | Notes |
|---|---|---|
| Submersible | Drilled wells, casing 4 in or larger | In the well, below frost; pull it to repair |
| Shallow-well jet | Water less than 25 ft down | Above ground; needs frost protection and priming |
| Deep-well jet | Water 25–250 ft down (Minnesota: usually under 200) | Lower pressure and yield than submersibles |
Pressure switch: typically starts the pump at 30 or 40 psi and stops it about 20 psi higher.
Tank pre-charge is 2 psi below the pump-on pressure (28 psi for a 30-psi start), measured with the tank drained and power off.
Tank size: about 4 × pump gpm (a 9-gpm pump needs about 36 gal). Only about 20% of a tank is usable water; a bigger tank alone won't fix a low-yield well.
Demand: 80–100 gal per person a day; size for a day's use in a 2-hour peak. A minimum of 6 gpm is suggested for most homes. A 1-gpm well gives 1,440 gal a day but only 120 gal in a 2-hour peak. A 6-in well stores about 1.5 gal per foot of water.
Livestock per day: milking cow 35 gal, beef cow or horse 12, sheep or goat 2, swine 1.5, chickens 9 per 100.
Sources: Nebraska Extension, Minnesota Department of Health, Well Management Section and 1 more
- Nebraska Extension. Private Drinking Water Wells: The Distribution System (NebGuide G2152)
- Minnesota Department of Health, Well Management Section. Well Owner's Handbook: A Consumer's Guide to Water Wells in Minnesota (4th ed., updated January 2014)
- Nebraska Extension. Private Drinking Water Wells: Operation and Maintenance for Mechanical Components (NebGuide G2153)
- Penn State Extension. Using Low-Yielding Wells
- Penn State Extension. Water System Planning: Estimating Water Needs
Safety
Sources: Minnesota Department of Health, Virginia Cooperative Extension and 4 more
- Minnesota Department of Health. Well Disinfection (handout, revised 05-10-2023)
- Virginia Cooperative Extension. Virginia Household Water Quality Program: Shock Chlorination: Disinfecting Private Household Water Supply Systems (Publication 442-663)
- CDC. How to Disinfect Wells After an Emergency
- U.S. EPA Office of Water. What to Do After the Flood (EPA 816-F-05-021, August 2005, updated October 2024)
- Minnesota Department of Health, Well Management Section. Well Owner's Handbook: A Consumer's Guide to Water Wells in Minnesota (4th ed., updated January 2014)
- Minnesota Department of Health, Well Management Section. Hydrogen Sulfide and Sulfur Bacteria (fact sheet)
- U.S. Occupational Safety and Health Administration. Confined Spaces - Overview (OSHA Safety and Health Topics)
- U.S. Occupational Safety and Health Administration. 29 CFR 1910.146 — Permit-required confined spaces (definitions)
- CDC. Confined Spaces and Safety (NIOSH Publication No. 2026-109, with CPWR)
- CDC. Carbon Monoxide Poisoning Basics (generator section)
Flooded wells
Sources: U.S. EPA Office of Water, U.S. Environmental Protection Agency and 2 more
- U.S. EPA Office of Water. What to Do After the Flood (EPA 816-F-05-021, August 2005, updated October 2024)
- U.S. Environmental Protection Agency. Protect Your Home's Water
- CDC. How to Disinfect Wells After an Emergency
- Pennsylvania Department of Health. Private Well Water (fact sheet, September 2022)
Shock chlorination
Use it after construction, any repair, a positive coliform test or flooding, and not as a cure for recurring bacteria. Find and fix the source (a failing septic system, loose cap, cracked casing). Penn State found it kept contaminated wells clean for a year in only about 15% of cases.
Sources: Penn State Extension, Virginia Cooperative Extension and 7 more
- Penn State Extension. Shock Chlorination of Wells and Springs
- Virginia Cooperative Extension. Virginia Household Water Quality Program: Shock Chlorination: Disinfecting Private Household Water Supply Systems (Publication 442-663)
- University of Georgia Extension. Disinfecting Your Well Water: Shock Chlorination (Circular 858-4)
- Pennsylvania Department of Environmental Protection. Disinfection of Home Wells and Springs
- CDC. How to Disinfect Wells After an Emergency
- Minnesota Department of Health. Well Disinfection (handout, revised 05-10-2023)
- U.S. EPA Office of Water. What to Do After the Flood (EPA 816-F-05-021, August 2005, updated October 2024)
- Georgia Department of Public Health. Shock Chlorination: Disinfecting Your Well (instruction sheet)
- Utah Division of Water Rights, Office of the State Engineer. State of Utah Water Well Handbook Based on the Administrative Rules for Water Wells (R655-4 UAC), July 2022 version
Troubleshooting
| Problem | Likely cause | What to do |
|---|---|---|
| No water | Power, breaker, or pump set too high in a drought | Check the breaker, then call a pro |
| Pump runs constantly | Stuck check valve or a line break | Look for a soggy spot; call a pro |
| Pump cycles a few seconds | Too little air in the pressure tank | Check the pre-charge (power off) |
| Sand in the water | Poorly built well or a hole in the screen | Contractor |
| Rotten-egg smell, hot tap only | Water-heater anode | Replace or remove the anode |
| Rotten-egg smell, both taps | Sulfur bacteria or hydrogen sulfide | Test coliform and nitrate; treat |
Sources: Nebraska Extension, Minnesota Department of Health, Well Management Section
- Nebraska Extension. Private Drinking Water Wells: Operation and Maintenance for Mechanical Components (NebGuide G2153)
- Minnesota Department of Health, Well Management Section. Well Owner's Handbook: A Consumer's Guide to Water Wells in Minnesota (4th ed., updated January 2014)
- Minnesota Department of Health, Well Management Section. Hydrogen Sulfide and Sulfur Bacteria (fact sheet)
Costs (dated)
Drilling anchors are old livestock-well scenarios, not current prices: NRCS FY2014–15 about $37 a foot for 6-in drilled wells of about 100 ft (Iowa, Missouri), $17–$29 a foot for 300–400 ft wells, $147–$195 a foot for dug or large-diameter wells.
Sources: USDA Natural Resources Conservation Service, Iowa, USDA Natural Resources Conservation Service, Arkansas and 2 more
- USDA Natural Resources Conservation Service, Iowa. NRCS Iowa Scenario Cost: Practice 642 - Water Well (FY2015, compiled 12/23/2014)
- USDA Natural Resources Conservation Service, Arkansas. NRCS Arkansas Scenario Cost: Practice 642 - Water Well (FY2015, compiled 1/12/2015)
- USDA Natural Resources Conservation Service, Missouri. NRCS Missouri Scenario Cost: Practice 642 - Water Well (FY2014, compiled 12/6/2013)
- USDA Natural Resources Conservation Service, Connecticut. NRCS Connecticut Scenario Cost: Practice 642 - Water Well (FY2015, compiled 10/27/2014)
Common mistakes
Never testing a private well, or testing only once.
Siting a well or a manure pile too close to each other or to a septic field.
Turning on a flooded well's pump before the wiring is checked.
Using scented or pool bleach for shock chlorination, or flushing the chlorinated water into the septic system or garden.
Sources: CDC, Washington State Legislature and 3 more
- CDC. Guidelines for Testing Well Water
- CDC. Well Water Safety
- Washington State Legislature. WAC 173-160-171 — What are the requirements for the location of the well site and access to the well?
- U.S. EPA Office of Water. What to Do After the Flood (EPA 816-F-05-021, August 2005, updated October 2024)
- Minnesota Department of Health. Well Disinfection (handout, revised 05-10-2023)
- University of Georgia Extension. Disinfecting Your Well Water: Shock Chlorination (Circular 858-4)
Resources
- ResourceCDC: Well water safetyNational minimum distances from septic systems, livestock yards and storage.
- ResourceEPA: What to do after the floodFlooded wells, the pump and the owner disinfection method.
- ResourceWell owner's handbook (Minnesota Department of Health)Well construction, pumps and maintenance.
- ResourceOperation and maintenance for mechanical components (Nebraska Extension)Pressure switches, tanks and troubleshooting.
- Related guideFiltration and purificationTesting and treating your well water.
By zone
Frost depth and local rules shape how a well is built. Here is what shifts by zone and region.
- 3–4
- Pitless adapters and pits matter for wells. Test for arsenic and radon in rock wells.
Where this comes from
Every fact in this lesson was checked against 46 published sources, all from extension services, the USDA and research journals. Each section lists its own at the bottom.
See all 46 sources
- CDC
- Penn State Extension
- Colorado State University Extension
- Minnesota Department of Health, Well Management Section
- Nebraska Extension
- U.S. Environmental Protection Agency
- U.S. Occupational Safety and Health Administration
- Colorado Division of Water Resources
- Colorado Division of Water Resources, Department of Natural Resources
- Colorado Water Quality Control Commission
- Florida Legislature
- Georgia Department of Public Health
- Georgia Department of Public Health, Environmental Health
- Minnesota Department of Health
- Minnesota Pollution Control Agency
- New York State Department of Health
- North Carolina Office of Administrative Hearings
- Pennsylvania Department of Environmental Protection
- Pennsylvania Department of Health
- Texas A&M AgriLife Extension Service
- Texas A&M AgriLife Extension Service, Texas Well Owner Network
- U.S. EPA Office of Water
- U.S. Geological Survey
- University of Georgia Extension
- USDA Natural Resources Conservation Service, Arkansas
- USDA Natural Resources Conservation Service, Connecticut
- USDA Natural Resources Conservation Service, Iowa
- USDA Natural Resources Conservation Service, Missouri
- Utah Division of Water Rights
- Utah Division of Water Rights, Office of the State Engineer
- Virginia Cooperative Extension
- Washington State Department of Ecology
- Washington State Legislature
- Wisconsin Legislative Reference Bureau
Summary
The whole lesson on one page. Print it or come back to it.
Key information
- Test a private well every year for total coliform, nitrate, TDS and pH at a state-certified lab, and again after floods, repairs or a change in taste or smell.
- Keep a well 50 ft or more from septic tanks and livestock yards and 100 ft or more from drain fields in most states. Check your state's table.
- Don't turn on a flooded well's pump until a qualified person checks the wiring, and never enter a well pit.
- Shock chlorination is not a cure for recurring bacteria. Find and fix the source, and follow one agency's whole procedure.
- Pressure-tank pre-charge is 2 psi below the pump-on pressure (28 psi for a 30-psi start), measured with the tank drained and power off.
- Know your water right. In Colorado, Utah and other western states you can't use some wells outdoors without one.
Step by step
- 1.Site the well at the highest practical spot, not down slope from contamination.
- 2.Check your state's rules on driller licenses, permits, setbacks and water rights.
- 3.Protect the wellhead: casing above ground, ground sloped away, and a vermin-proof, weatherproof cap with a screened vent.
- 4.Match the pump type to how far down the water is, then set the pressure switch and tank pre-charge.
- 5.Test the water every year, and after a flood or repair.
Links to products
- Sanitary well capVermin-proof and weatherproof, with a screened vent.
- Pressure tankSized to the pump's gpm.
- Pressure gaugeTo check the tank pre-charge with the power off.
- VoltmeterTo verify power is off before anyone works on the pump.
- Unscented household bleachPlain, with no additives, for shock chlorination.
- Battery carbon monoxide detectorFor any place a generator runs nearby.
Made it to the end? I’ll keep track for you on this device.

